" type="text/css" media="screen" />
 

FALSE ALARM TRIGGER

AUTO-ARMAMENT

120db DOUBLE ALARM SIREN

KEYLESS OPERATION, MORE THEN 16,000 POSSIBLE CODES

THICK ANTI - SHOCK CASING

ALL WEATHER OPERATION

NO ELECTRO-MECHANISM CONTACT ELIMINATING POSSIBLE CORROSION

EFFICIENT IN ALL AXES


FALSE ALARM TRIGGER

Did you know that over 90% of alarms are false? We took this fact into consideration. We did not want an alarm that increased the noise levels of our surroundings unnecessarily.



The Anti-theft & Personal portable alarm system can eliminate false alarms. If the item being protected is moved accidentally or the alarm senses an unusual amount of vibration, the alarm triggers a super loud single "beep" warning any would be thief that the item is protected.



The process of detecting movement, warning and checking again for movement, takes less than a second. After the warning signal, if the item is still being moved, the system will trigger the blasting horn of the siren for 15 second and start to check and warn and trigger the blasting horn of the siren again and again as long as your item is moving. With all the different sounds coming from the alarm it is bound to get attention and any thief would immediately drop the item and run! Thefts don't like to draw attention to themselves.

You can adjust the alarm warning signal from 0 warnings to 7 warnings per minute. This enables you to 'fine tune' the level of protection dependant on the environment. No other portable alarm system offer you this level of control.


Return to top  


AUTO - ARMAMENT

An alarm is only going to protect your goods when it is turned on. There is a vast array of reasons why one would forget or simply not bother to turn on an alarm. For this reason our alarm has a built in auto-armament option.



Once selected, the system waits until it detects that there has been no movement or vibration on the item for 15 seconds. Then, at 10 seconds countdown, the system will notify you of its imminent self-armament, by producing a low volume little BEEP during the last 5 seconds countdown.

At this time, if you don't want self-armament, all you have to do is move the item and the countdown stops immediately and the system start to monitor a lack of movement again. The self-armament countdown can be set-up for up to 2 minutes delay. Once auto-armament has been set the alarm will sound if the item is moved. By simply entering the personal code the alarm will not sound, however, the auto-armament feature will remain active until specifically set of.



Only you will be able to remove the auto-armament option, because you can set your private deactivation code which can be different from the code to disarm the alarm. This way, nobody will be able to remove the auto armament option and your investment will always be protected.



This will be helpful to many people and applications. For example, many parents will buy our alarm system or a D-lock to protect their child's bicycle. However, they never know if the child will take the time to arm or lock the bicycle. Our research shows that many children don't! With this system, you can activate the auto armament option so when the child wants to use his bicycle, the personal code will need to be entered first to prevent the alarm sounding.

Nobody on the portable alarm system industry can guarantee you this huge 24 hours a day protection !

Return to top  


DOUBLE ALARM SIREN

Believe it or not, most portable alarm systems can be muffled with just one hand. Our alarm is designed to prevent this and provide even more outdoor protection!

Since every portable alarm system on the market have only one piezo to produce sound and since the sound dispersion is made from only one cavity, it is possible not to hear the siren if the sound is being pushed in the opposite direction of your ears and there are no surfaces for the sound to rebound.

For example you could be inside the house and your bike could be outside, or you could be in the backyard while your bicycle is being tampered with.

The outstanding design feature of this alarm system allows it to provide a surround blasting sound of 130 db at each end of the system. This means that it is almost impossible to muffle once installed on your valuable item!

The sound is coming out from both end and all around the both ends !



This means that it can be heard perfectly many hundred feet away.

Once again, nobody else is offering such a high quality & efficient portable alarm system!

Return to top  




KEYLESS OPERATION, MORE THEN 16,000 POSSIBLE CODES

The portable alarm system is keyless in operation and has over 16,000 possible combinations.


 
In fact, on the keypad, 3 keys are available and the code is made with 5 numbers. Each of these 5 numbers can be a combination of one, two or 3 keys together.  For example, the code can be easy as 1 - 1 - 2 - 2 - 2, or it could be 12 - 3 - 23 - 13 - 123.

The portable alarm system will automatically trigger the  blasting horn of the siren after 2 bad 5 numbers code sequence have been entered.  This will prevent anyone attempting to work out the reset code.

 

The portable alarm system will automatically trigger the blasting horn of the siren after 2 bad 5 numbers code sequence have been entered.

This will prevent anyone attempting to work out the reset code.


Return to top  



THICK ANTI - SHOCK CASING

Thick anti shock casing is provide on the alarm system to support extreme conditions. It is resist to the hammer, pair of pliers, etc... You can be sure that thefts will think twice before touching your goods, because the portable alarm system will warn and alert you long before it is destroyed.

Return to top

ALL WEATHER OPERATION

The portable alarm system is designed to resist to all weather conditions. Rain, dust, snow and even deep cold won't stop it! The 9 volts alkaline battery needed to operate the system will provide enough power to protect your goods for many hours in extremely cold conditions or many months normal temperature. Perfect for protecting expensive ski equipment while you're enjoying a bit of apres ski!

Return to top  




NO ELECTRO-MECHANISM CONTACT ELIMINATING POSSIBLE CORROSION

Yes we did it!!! Advance engineering and use of micro-processor allows the personal portable alarm system to operate without any electro-mechanism contact eliminating possible corrosion of the detection device.

No one else is offering such a high quality & efficient portable alarm system on the market! The reason is simple, it is too expensive to manufacture.

Return to top  


EFFICIENT IN ALL AXES



First of all let us explain how most existing alarm systems detect movement. It is done with the help of a metallic ball bearing displacement from 2 studs to another 2 studs. See Fig A below. This graphic shows a standard detection device.

To notice a movement the metallic ball which is making electrical contact with the 2 lower studs (1&2) has to be moved by applying a 90 degree rotation on the system.



Fig A.

The ball will then leave contact studs 1 & 2 and it will make contact between the studs 2 & 3. This will notify the system of a movement.

Figure B. shows an example of how you could move this unit in these ( ) directions and it will not trigger the alarm.



Figure B.

Using our unique design the personal alarm system can detect shock or movement on all axes.



 


The system detects the movement by vibrations made by a ball bearing rolling inside the plastic casing.

In fact it is the vibrations made on the piezo through the plastic casing that trigger the portable alarm system. It is computer driven!

There are no electro-mechanism contact, no possible oxidation and the ball is free to roll in any direction to produce vibrations.

There are even 2 balls in each portable alarm system to detect movement of your goods!

For example, if you place my Anti-theft & Personal portable alarm system on garden gate, it will warn you of anyone tries to pass over it. My system will notice you, but I am not sure the other systems will, because of their conception.

Some systems are using a spring that move and make contact inside a ring for the system to react, but once again, the oxidation will rapidly disable the system when used outside, causing corrosion and preventing the low current to pass between the spring and the fixed part of the detection device.

Return to top